ø2.0 ø3.0 ø3.3 ø3.6
7 TDE2007LC 3D3007LC01 - -
8.5 TDE2008LC 3D3008LC01 - -
10 TDE2010LC 3D3010LC01 - -
11.5 TDE2011LC 3D3011LC01 3D3311LC01 3D3611LC01
13 TDE2013LC 3D3013LC01 - -
  ø3.8 ø4.1 ø4.3 ø4.6
7 3D3807LC01 - - -
8.5 3D3808LC01 - - -
10 3D3810LC01 - - -
11.5 3D3811LC01 3D4111LC01 3D4311LC01 3D4611LC01
13 3D3813LC01 - - -
  • ㆍPackage unit : each part
  • ㆍLong stopper (6 mm) : Posterior surgery may be performed even without drill extension
  • ㆍThe color coding on the stopper indicates the drill length
  • ㆍThe tip length of a 2.0 twist drill is 0.6 mm, and the other tip length of drills, 0.8mm~1mm


  ø2.0 ø2.7 ø3.0 ø3.15 ø3.3
13 TDE2013FNLC   3D3013FNLC    
16 TDE2015FNLC 3D2715FNLC01 3D3015FNLC01 3D3115FNLC01 3D3315FNLC01
  ø3.6 ø3.8 ø4.1 ø4.3 ø4.6
13   3D3813FNLC     3D4613FNLC
16 3D3615FNLC01 3D3815FNLC01 3D4115FNLC01 3D4315FNLC01 3D4615FNLC01
  • ㆍPackage unit : each part
  • ㆍCuts the stopper of a 15 mm drill to facilitate depth adjustment in the ridge
  • ㆍThe laser marking indicates the length, thereby enabling all drilling lengths (7-15 mm) using one drill
  • ㆍHandles are color-coded to indicate drill length


  ø2.0 ø2.7 ø3.0 ø3.15 ø3.3
  TDE2015FNEC 3D2715FNEC 3D3015FNEC 3D3115FNEC 3D3315FNEC
  ø3.6 ø3.8 ø4.1 ø4.3 ø4.6
  3D3615FNEC 3D3815FNEC 3D4115FNEC 3D4315FNEC 3D4615FNEC
  • ㆍPackage unit : each part
  • ㆍFor sufficient intermaxillary gap as in the anterior part, drilling may be performed even without drill extension
  • ㆍThe laser marking indicates the length, thereby enabling all drilling lengths (7-15 mm) using one drill
  • ㆍHandles are color-coded to indicate drill length


①/ ②/ ③ ø2.2/3.0 ø3.0/3.6 ø3.0/3.6/4.1 ø3.0/4.1/4.6
Short 2D2230S 2D3036S 2D3041S 2D3046S
Long 2D2230L 2D3036L 2D3041L 2D3046L
Coloring Yellow Green Blue Red
Y-Dim. 0.7mm
  • ㆍPackage unit : each part
  • ㆍThe color of 123drill handle part means the diameter and kind of main mixture to be used
    - Yellow: F3.5, Green: F4.0, Blue: F4.5, Red: F5.0
  • ㆍInstall the drill stop in order to adjust the drilling depth to intended level
  • ㆍ123 twist drill has good cutting force and control of drilling depth may be difficult; therefore, it is highly recommended to use the drill stop


  ODS06 ODS07 ODS08 ODS09 ODS11 ODS12 ODS14 ODS16
L(mm) 6.2 7 8 9.5 11 12.5 14 15
Coloring Purple White Yellow Red Blue Green Black Purple
  • ㆍPackage unit : each part
  • ㆍThe length of drill stop means the remained actual length when the drill stop is installed on 123 twist drill
  • ㆍThe lengths are differentiated with colors for convenient identification of lengths and return to KIT

Name D1 D2 Code
ø4.6 Twist Drills ø4.6 - 3D4613FNLC
ø5.2 Direct Drill ø4.6 ø5.2 3D5213FNLC
ø5.5 Direct Drill ø4.6 ø5.5 3D5513FNLC
ø6.2 Direct Drill ø5.5 ø6.2 3D6213FNLC
ø6.5 Direct Drill ø5.5 ø6.5 3D6513FNLC
  • ㆍDirect drill: 2-stepped drill equipped with both pilot and twist drill function
    1. Enables final drilling without pilot drilling
    2. Enhancement of initial fixation in the extract socket by decreasing the dead space at the apex area

  ø3.5 ø4.0 ø4.5 ø5.0
7 TPD3C3507 TPD3C4007 TPD3C4507 TPD3C5007
8.5 TPD3C3508 TPD3C4008 TPD3C4508 TPD3C5008
10 TPD3C3510 TPD3C4010 TPD3C4510 TPD3C5010
11.5 TPD3C3511 TPD3C4011 TPD3C4511 TPD3C5011
13 TPD3C3513 TPD3C4013 TPD3C4513 TPD3C5013
15 TPD3C3515 TPD3C4015 TPD3C4515 TPD3C5015
Length of Drill Tip 0.8mm 0.9mm 1.0mm 1.0mm
  • ㆍPacking Unit : each part
    1. Enables final drilling without pilot drilling
  • ㆍProcessing exclusive use Taper Drill for III fixture diameter and length
  • ㆍStopper drill with 1mm margin
  • ㆍColor coding on the shank indicates the fixture diameter
    (ø3.5:Yellow, ø4.0:Green, ø4.5:Blue, ø5.0:Red )
  ∅6.0 ∅7.0
6 TPD3C6006 TPD3C7006
7 TPD3C6007 TPD3C7007
8.5 TPD3C6008 TPD3C7008
10 TPD3C6010 TPD3C7010
11.5 TPD3C6011 TPD3C7011
13 TPD3C6013 TPD3C7013
  • ㆍPacking Unit : each part
  • ㆍProcessing exclusive use Taper Drill for Taper Ultra-Wide fixture diameter and length
  • ㆍStopper drill with 1mm margin
  • ㆍColor coding on the shank indicates the fixture diameter
    (ø6.0 : Green, ø7.0 : Blue)
Type Code
Lance Drill Short AGDSC
Long AGDLC
  • ㆍPacking Unit : each part
  • ㆍForms holes in the bone to facilitate initial drilling
  • ㆍBone density can be determined through drilling
  • ㆍTiN coating improves anti-corrosion and wear resistance
  ø2.0
Code GD2027L
  • ㆍPacking Unit : each part
  • ㆍUsed as the initial drill
  • ㆍInstall the drill stop in order to adjust the drilling depth to intended level
  D1 D2 L
OSLMDS 1.5 2.0 13.0
OSLMDL 1.5 2.0 20.0
OSLMD20S 2.0 2.5 13.0
OSLMD20L 2.0 2.5 20.0
  • ㆍPacking Unit : each part
  • ㆍEnables the bodily change of drilling direction
  • ㆍUsed to cut the ridge of the extracted socket
  • ㆍFacilitates site preparation in the extracted socket
Code ADE
  • ㆍPacking Unit : each part
  • ㆍExtends the length a drill and other hand tools
  • ㆍUse by connecting the flat side of the drill handle to the flat side of the drill extension
  • ㆍThe use of too much force is prohibited
øA øB Mini Regular Wide
2.0 2.7 APD270C - -
2.0 3.0 - APD300C -
3.0 3.8 - - APD380C
3.0 4.1 - - APD410C
  • ㆍPacking Unit : each part
  • ㆍUsed for the path adjustment of a drilling hole
  • ㆍWhen using the next size drill, the guide hole enables precise cutting
  • ㆍTiN coating improves anti-corrosion and wear resistance
  F3.5 F4.0 F4.5 F5.0
II type 2CD35 2CD40 2CD45 2CD50
III type 3CD35 3CD40 3CD45 3CD50
Coloring Yellow Green Blue Red
  • ㆍPacking Unit : each part
  • ㆍIt is recommended to drill up to the lower end of the marking line
  • ㆍThe marking line of II type cortical drill is based on hard bone
  • ㆍThe lower end marking line of III type cortical drill is based on normal bone and the upper end marking line is based on hard bone
  • ㆍThe color of handle part means the diameter and kind of main mixture to be used
  • ㆍThe color of handle part means the diameter and kind of main mixture to be used

    - Yellow: F3.5, Green: F4.0, Blue: F4.5, Red: F5.0
Spec. ø3.5 ø4.0 ø4.5 ø5.0
Code CD2C35 CD2C40 CD2C45 CD2C50
  • ㆍPacking Unit : each part
  • ㆍUse after formation of final drill hole in case of hard bone(D1)
  • ㆍThe marking line of II type cortical drill is based on hard bone
  • ㆍExclusive drills are available to meet the fixture diameters
  • ㆍIt is recommend that drilling performs up to under marking line
Spec. ø3.5 ø4.0 ø4.5 ø5.0
Code CD2C35 CD2C40 CD2C45 CD2C50
  • ㆍPacking Unit : each part
  • ㆍDrills for expansion of cortical bone after use of straight drill
  • ㆍUse after formation of final drill hole in case of more than normal bone
  • ㆍExclusive drills are available to meet the fixture diameters
  • ㆍThe lowest marking line is normal bone and the highest marking line is hard bone
  • ㆍIt is recommend that drilling performs up to marking line
Spec. ø3.5 ø4.0 ø4.5 ø5.0
Code TCD4C35 TCD4C40 TCD4C45 TCD4C50
  • ㆍPacking Unit : each part
  • ㆍDrills for expansion of cortical bone after use of taper drill
  • ㆍUse after formation of final drill hole in case of more than hard bone
  • ㆍExclusive drills are available to meet the fixture diameters
  • ㆍLower end marking line is based on 8.5mm or smaller fixture implant
    Upper end marking line is based on 10mm or larger fixture implant
  • ㆍIt is recommend that drilling performs up to the bottom marking line
Name Code
F6.0 Cortical Dril CD4C60
F7.0 Cortical Dril CD4C70
  • ㆍUse after formation of final drill hole in case of hard bone(D1)
  • ㆍExclusive drills are available to meet the fixture diameters
  • ㆍIt is recommend that drilling performs up to the bottom marking line
øA øB Regularø4.1 Regularø4.8 Wideø4.8
3.5 4.8 ASCD350C - -
4.2 4.8 - ASCD420C -
4.2 6.0 - - ASCDW420C
  • ㆍPacking Unit : each part
  • ㆍForm fixture platform
  • ㆍCut up to the bottom of the laser marking
  • ㆍUse US Mini Countersink for SS Mini as needed
øA øB Mini Regular Wide
2.6 2.9 ACD330C - -
3.5 4.1 - ACD375C -
4.2 5.1 - - ACD500C
  • ㆍPacking Unit : each part
  • ㆍForm space of fixture flange
  • ㆍCut up to the bottom of the laser marking
Code USSCS45W
  • ㆍPacking Unit : each part
  • ㆍInstruments for Wide PS, Wide of USIII, USII SA, USIII SA
  • ㆍRecommendation drilling rpm : 300rp
Platform ø4.8 ø4.8 ø6.0
  ø4.1 ø4.8
Short OSST41SC OSST48SC
Long OSST41LC OSST48LC
  • ㆍPacking Unit : each part
  • ㆍUse for dense bone and form screw thread-shaped fixtures
  • ㆍUse a torque wrench after connecting to the engine or mount extension
  • ㆍTiN coating improves anti-corrosion and wear resistance
  3.3 3.75 4.0 5.0
Short 4.8 OUST37SC OUST40SC OUST50SC
Long OUST33LC OUST37LC OUST40LC -
  • ㆍPacking Unit : each part
  • ㆍUse for dense bone and form screw thread-shaped fixtures
  • ㆍUse as a torque after connecting to the engine or a simple mount extension
  • ㆍTiN coating improves anti-corrosion and wear resistance
Diameter(ø) Code
ø4.0 APP400
ø5.0 APP500
ø6.0 APP600
Full Set APPS
  • ㆍPacking Unit : Individual and general set packing
  • ㆍUse for checking the direction and location for bone preparation
  • ㆍPredicts the diameter of an abutment to be secured
D ø4.0 ø5.0
Code OPP400 OPP500
  • ㆍPacking Unit : each part
  • ㆍParallel Pin 123 Twist Drill only
  • ㆍUse for checking the direction and location for bone preparation
  • ㆍUse the lower part for initial drilling and higher part for F3.5 (ø2.2/3.0) drilling
Code ADG
  • ㆍPacking Unit : each part
  • ㆍA : Measurement of drilling length (7-15 mm)
  • ㆍB : Measurement of gingival height following external fixture grafting
Code ADG
  • ㆍPacking Unit : each part
  • ㆍUse as drilling depth measurement and open wrench
  • ㆍUse for separating Mount in case of soft bone
Diameter(D) ø5.2 ø5.0 ø6.2 ø6.5
Code UWFTP52 UWFTP55 UWFTP62 UWFTP65
  • ㆍPacking Unit : each part
  • ㆍCheck internal width and depth after extraction of a tooth
  • ㆍCheck the drilling depth after using direct drill as final drill
  • ㆍVerify the internal diameter of the failed implant socket
  • ㆍThe purpose of Parallel Pin
Diameter(ø) ø4.0 ø5.0
Code ASDG360 ASDG430
  • ㆍPacking Unit : each part
  • ㆍMeasure the depth after the final drilling
Length(mm) Code
7 ADP607
8.5 ADP608
10 ADP610
  • ㆍPacking Unit : Individual and general set packing
  • ㆍIt is enable to check the drilling depth easily due to convenient design of top part
Width(mm) Code
2.5 APG201
6 APG202
11 APG203
  • ㆍPacking Unit : Individual and general set packing
  • ㆍIndicates the distance between fixtures
  • ㆍUse after the first drilling (2.0)
Code GTHGS
  • ㆍPacking Unit: each part
  • ㆍMeasurement gingival height for selecting optimal abutment
  • ㆍNon gloss treatment for improving identification
Code TW30B
  • ㆍPacking Unit: each part
  • ㆍPossibility of loading 10, 20, 30 and infinite Ncm
  • ㆍUsed to adjust the installation location of implants or to tighten abutments or screws
  • ㆍThe last line is approx. 40 Ncm
  • ㆍTorque is applied to the center of the bar, which will be generated by pulling the bar
  • ㆍThe product should be cleaned after use, and then sterilized for storage
Code CITQW-1185A
  • ㆍPacking Unit: each part
  • ㆍPossibility of loading 10, 20, 30 and infinite Ncm
  • ㆍOnly surgical unlimited wrench (If excessive torque is applied, the inside of bone or fixture may be damaged.)
  • ㆍRotating direction is marked by an arrow for convenient identification
Type Mini Regular
Short GSNMD32S GSNMD35S
Long GSNMD32L GSNMD35L
  • ㆍPacking Unit: each part
  • ㆍTo enable the simultaneous measurement of gingival height upon treatment, grooves and laser markings are indicated at 1-mm (1-6 mm) intervals
  • ㆍStopper designed for the prevention of fracture of the holding part and occurrence of foreign matter such as blood stain during the surgery
Type Regular Wide
Short SSNOMD39RS
Long SSNOMD39RL
  • ㆍPacking Unit: each part
  • ㆍSince the shape is similar to that of the internal fixture driver, even a high torque does not change the inside of the fixture
  • ㆍStopper designed for the prevention of fracture of the holding part and occurrence of foreign matter such as blood stain during surgery
  Mini Regular Wide
Short USNMD35MS USNMD41RS USNMD51WS
Long USNMD35ML USNMD41RL USNMD51WL
  • ㆍPacking Unit: each part
  • ㆍTo enable the simultaneous measurement of gingival height upon treatment, grooves and laser markings are indicated at 1-mm (1-5 mm) intervals
  • ㆍStopper designed for the prevention of fracture of the holding part and occurrence of foreign matter such as blood stain during the surgery
Type Mini Regular
Short GSNMT32S GSNMT35S
Long GSNMT32L GSNMT35L
Extra Long GSNMT32E GSNMT35E
  • ㆍPacking Unit: each part
  • ㆍTo enable the simultaneous measurement of gingival height upon treatment, grooves and laser markings are indicated at 1mm intervals
  • ㆍStopper designed for the prevention of fracture of the holding part and occurrence of foreign matter such as blood stain during surgery
  • ㆍThe fracture strength : 260Ncm
  • ㆍIf excessive implant torque is applied, fracture may be resulted in; if unnecessary large implant torque is expected, use a fixture driver. Also, imperfect installation may result in fracture at the strength under fracture strength; therefore, perfect installation should be checked before use
  • ㆍSpecial attention should be paid; after occurrence of a fracture, restoration is impossible
Type Regular Wide
Short SSNOMD39RS
Long SSNOMD39RL
  • ㆍPacking Unit: each part
  • ㆍSince the shape is similar to that of the internal fixture driver, even a high torque does not change the inside of the fixture
  • ㆍStopper designed for the prevention of fracture of the holding part and occurrence of foreign matter such as blood stain during surgery
  • ㆍThe fracture strength : 260Ncm
  • ㆍIf excessive implant torque is applied, fracture may be resulted in; if unnecessary large implant torque is expected, use a fixture driver. Also, imperfect installation may result in fracture at the strength under fracture strength; therefore, perfect installation should be checked before use.
  • ㆍSpecial attention should be paid; after occurrence of a fracture, restoration is impossible.
Type Mini Regular
Short GSMFDS GSRFDS
Long GSMFDL GSRFDL
Extra Long GSMFDE GSRFDE
  • ㆍPacking Unit: each part
  • ㆍFixture connection
  • ㆍUse to place or remove a fixture after the separation of the mount
Plaftorm(ø) Regular Wide
Short SSRFDS
Long SSRFDL
  • ㆍPacking Unit: each part
  • ㆍThe laser marking is designed for checking during the connection of a fixture
  • ㆍUse for removal following fixture grafting and mount separation
Plaftorm(ø) Mini Regular Wide
Code USMFDL USRFDL USWFDL
  • ㆍPacking Unit: each part
  • ㆍThe laser marking is designed for easy identification during the connection of fixtures
  • ㆍUse for removal following fixture grafting and mount separation
Length Code
Short ASMDS
Long ASMDL
  • ㆍPacking Unit : each part
  • ㆍUse for fixture grafting by connecting to a simple mount
  • ㆍCompact design, internal holding function
Length Code
Short ASMES
Long ASMEL
  • ㆍPacking Unit : each part
  • ㆍUse for extension of simple mount length, and use in case of inputting hand-torque by connecting with ratchet wrench.
Code ASOW
  • ㆍPacking Unit: each part
  • ㆍFor weak bone, use to separate the simple mount
  • ㆍ30" neck angle enhances convenience of insertion in the oral cavity
Code Application
ERFM US Mini, TS Mini
HRFR US Regular, SS Regular/Wide, TS Regular
ERFW US Wide
  • ㆍPacking Unit : each part
  • ㆍWhen a fixture and the fixture mount are stuck, use after removing the fixture mount screw
  • ㆍUse after the connection to a driver handle and a torque wrench
  • ㆍInsert vertically and rotate clockwise

Tissue
Punch
A ø3.3 ø3.8 ø4.3 ø4.8 ø5.3
Code OSTP33 OSTP38 OSTP43 OSTP48 OSTP53
Application Healing Abutment Standard TS ø4.0/ø4.5 ø4.5/ø5.0 ø5.0 ø6.0 ø6.0
SS - ø4.8 - ø6.0 ø6.0
US ø4.0 ø5.0 ø5.0 ø6.0 ø6.0
It is recommended to use the tissue punch that has the diameter smaller than that of healing abutment by 0.7~1.5mm.
  • ㆍPacking Unit: Tissue Punch + Guide Pin
  • ㆍTool to be used for flapless surgery
  • ㆍThe laser marking at 2-mm intervals enables the measurement of gingival height
Connection Healing
abutment
dia.
Bone Profiler type
Mini
&
Regular
ø4.5 GSBP45
ø5.5 GSBP55
ø6.5 GSBP75
ø7.5
Guide Screw
Mini
Connection
Regular
Connection
  • ㆍPacking Unit : Bone Profiler + Guide Screw
  • ㆍUse to remove the bone around the fixture during the first or second surgery
  • ㆍIt is used for compensation of the shape of healing abutment by eliminating the bone after connection of guide screw with the fixture
  • ㆍThe guide screw protects the morse taper of the fixtures
Code Inner Dia(ø) Outer Dia(ø) Length
TD37S 3.7 4.5 Short
TD42S 4.2 5.0 Short
TD47S 4.7 5.5 Short
TD52S 5.2 6.0 Short
TD62S 6.2 7.0 Short
TD37 3.7 4.5 Long
TD42 4.2 5.0 Long
TD47 4.7 5.5 Long
TD52 5.2 6.0 Long
TD62 6.2 7.0 Long
  • ㆍPacking Unit : each part
  • ㆍUse for the collection of bone or removal of damaged or failed fixtures
  • ㆍUse for removal of Septal bone
  • ㆍTrephine drill can be used as initial drill when to implant Ultra Fixture
Code ABM
  • ㆍPacking Unit: each part
  • ㆍForms particulate bone using the collected autogenous bone